ST7565P
65 x 132 Dot Matrix LCD Controller/Driver
Product Description
The ST7565P is a single-chip dot matrix LCD driver that can be connected directly to a microprocessor bus. 8-bit parallel or serial display data sent from the microprocessor is stored in the internal display data RAM and the chip generates a LCD drive signal independent of the microprocessor. Because the chips in the ST7565P contain 65x132 bits of display data RAM and there is a 1-to-1 correspondence between the LCD panel pixels and the internal RAM bits, these chips enable displays with a high degree of freedom.
The ST7565P chips contain 65 common output circuits and 132 segment output circuits, so that a single chip can drive a 65x132 dot display (capable of displaying 8 columnsx4 rows of a 16x16 dot kanji font).
Moreover, the capacity of the display can be extended through the use of master/slave structures between chips. The chips are able to minimize power consumption because no external operating clock is necessary for the display data RAM read/write operation. Furthermore,because each chip is equipped internally with a low-power LCD driver power supply, resistors for LCD driver power voltage adjustment and a display clock CR oscillator circuit, the ST7565P can be used to create the lowest power display system with the fewest components for high-performance portable devices.
Features - Direct display of RAM data through the display data RAM.
- RAM capacity : 65 x 132 = 8580 bits
- Display duty selectable by select pin
-- 1/65 duty : 65 common x 132 segment
-- 1/49 duty : 49 common x 132 segment
-- 1/33 duty : 33 common x 132 segment
-- 1/55 duty : 55 common x 132 segment
-- 1/53 duty : 53 common x 132 segment
- High-speed 8-bit MPU interface (The chip can be connected directly to the both the 80x86 series MPUs and the 68000 series MPUs) / Serial interfaces are supported.
- Abundant command functions Display data Read/Write, display ON/OFF, Normal/Reverse display mode, page address set, display start line set, column address set, status read, display all points ON/OFF, LCD bias set, electronic volume,
read/modify/write, segment driver direction selects, power saver, static indicator, common output status select, Vo voltage regulation internal resistor ratio set.
- Static drive circuit equipped internally for indicators.(1 system, with variable flashing speed.)
- Low-power liquid crystal display power supply circuit equipped internally. Booster circuit (with Boost ratios of 2X/3X/4X/5X/6X, where the step-up voltage reference power supply can be input externally).
- High-accuracy voltage adjustment circuit (Thermal gradient ¡V0.05%/¢XC ) V0 voltage regulator resistors equipped internally, V1 to VSS voltage divider resistors equipped internally, electronic volume function equipped internally, voltage follower.
- CR oscillator circuit equipped internally (external clock can also be input)
- Extremely low power consumption Operating power when the built-in power supply is used (an example)
60uA (VDD ¡V VSS = VDD2 ¡V VSS =3.0 V, Quad voltage, V0 ¡V VSS = 11.0 V). Conditions: When displays pattern OFF and the normal mode is selected.
- Power supply operate on the low 1.8 voltage Logic power supply
-- VDD ¡V VSS = 1.8V to 3.3 V (+10% Range)
-- Boost reference voltage: VDD2 ¡V VSS = 2.4V to 3.3V
-- Booster maximum voltage limited
-- VOUT= 16.0V (+10% Range)
-- Liquid crystal drive power supply: V0 ¡V VSS = 4.0V to 13.0 V
- Wide range of operating temperatures: ¡V40 to 85¢XC
- CMOS process
- Shipping forms include bare chip and TCP.
- These chips not designed for resistance to light or resistance to radiation.
Downloads
|
![](http://www.sitronix.com.tw/images/dot.gif") |